Chủ Nhật, 4 tháng 12, 2016

Proxmox VE- One Public IP

Proxmox VE - One Public IP
This guide will show you how to set up Proxmox with only one public IP. We will configure an extra interface bridge and make sure VM traffic is NATed. I have a few dedicated servers, some run Proxmox. Most of them however have only a few IP's. Therefore the VM's in proxmox cannot all have a public IP. For most of them that is not a problem. If needed I run a proxy or set up iptables to forward ports to the VM's.
This guide is tested on a proxmox machine running proxmox version 3.2.
What we will have at the end is a VM with an SSH port reachable on the public IP:
Container/VM ------------ Proxmox Server -------------- Public Internet
10.21.21.5:22 --- 10.21.21.5:22 NAT to 1.2.3.4:2222 --- 1.2.3.4:2222
Proxmox by default creates one interface, vmbr0. That config looks like this:
# /etc/network/interfaces
auto vmbr0
iface vmbr0 inet static
   address 1.2.3.4
   netmask 255.255.255.0
   network 1.2.3.0
   broadcast 1.2.3.255
   gateway 1.2.3.1
   bridge_ports eth0
   bridge_stp off
   bridge_fd 0
Replace 1.2.3.X with your public ip, network, gateway and such. Do note that there might be more interfaces, like vmbr1 for ipv6.
We create a new bridge which will enable NAT when the interface gets UP. Add the following to the file:
# /etc/network/interfaces:
auto vmbr2
iface vmbr2 inet static
   address 10.21.21.254
   netmask 255.255.255.0
   bridge_ports none
   bridge_stp off
   bridge_fd 0
   post-up echo 1 > /proc/sys/net/ipv4/ip_forward
   post-up iptables -t nat -A POSTROUTING -s '10.21.21.0/24' -o vmbr0 -j MASQUERADE
   post-down iptables -t nat -D POSTROUTING -s '10.21.21.0/24' -o vmbr0 -j MASQUERADE
   post-up iptables -t nat -A PREROUTING -i vmbr0 -p tcp --dport 2222 -j DNAT --to 10.21.21.5:22
   post-down iptables -t nat -D PREROUTING -i vmbr0 -p tcp --dport 2222 -j DNAT --to 10.21.21.5:22
The first part:
address 10.21.21.254
netmask 255.255.255.0
bridge_ports none
bridge_stp off
bridge_fd 0
defines the IP address and subnet mask of the new interface. It also tells the network stack that the bridge has no actual ports (like eth0) and that the Spanning Tree Protocol should be disabled.
post-up echo 1 > /proc/sys/net/ipv4/ip_forward
Enables IP forwarding when this interface gets up. This allows the machine to forward packets.
post-up iptables -t nat -A POSTROUTING -s '10.21.21.0/24' -o vmbr0 -j MASQUERADE
post-down iptables -t nat -D POSTROUTING -s '10.21.21.0/24' -o vmbr0 -j MASQUERADE
These two lines enable the actual NAT-ing of packets from the source network '10.21.21.0/24' and vmbr0 as the output interface. If your WAN interface has a different name, change that here. The first line enables the natting when the interface gets up, the second line deletes the firewall rule when the interface goes down.
post-up iptables -t nat -A PREROUTING -i vmbr0 -p tcp --dport 2222 -j DNAT --to 10.21.21.5:22
post-down iptables -t nat -D PREROUTING -i vmbr0 -p tcp --dport 2222 -j DNAT --to 10.21.21.5:22
These two rules enable and disable the actual port forwarding of tcp port 2222 on the WAN IP to tcp port 22 on internal IP address 10.21.21.5. Here as well the WAN interface (this time, the input interface) is vmbr0.
If you for example want to expose tcp port 80 of a VM with IP 10.21.21.6 on the public IP's port 80, you should also add these lines:
post-up iptables -t nat -A PREROUTING -i vmbr0 -p tcp --dport 80 -j DNAT --to 10.21.21.6:80
post-down iptables -t nat -D PREROUTING -i vmbr0 -p tcp --dport 80 -j DNAT --to 10.21.21.6:80
When you create a KVM VM, make sure it is attached to the bridge vmbr2. It should also have a static IP configured in the range you define. OpenVZ venet interfaces with an IP in this range automagiaclly work.
Don't forget to restart the network afterwards:
/etc/init.d/networking restart

Không có nhận xét nào:

Đăng nhận xét